Search filter

Supplemental sheet for Slimdrive EMD Invers link arm mounting

XX Slimdrive EMD invers DE Montageanleitung Markierung (4) setzen, wie weit der innere Schenkel (6) in den äußeren Schenkel (8) eingeschoben werden muss. DE Gestänge  Anschlagmaße Kopfmontage Bandgegenseite Anschlagmaße für Montageplatte DIN rechts/links spiegelbildlich  Anschlagmaße für Direktbefestigung DIN rechts/links spiegelbildlich     XX 179938-01 XX XX    Hebel (7) an Abtriebswelle montieren und wie markiert aufsetzen. Teleskopstange (5) an Tür montieren. Teleskopschenkel bis zur Markierung (4) ineinander­schieben. Hebel (7) dabei ca. 5° vorspannen. Gestänge-Lagerbock montieren Bei der Verwendung des Sensorgestänges separate Montageanleitung beachten. XX Gestänge-Lagerbock (1) mit … Schrauben festschrauben.       XX Teleskopschrauben (3) anziehen, Anzugs­drehmoment 15 Nm. Gestänge montieren XX XX Tür (2) öffnen und Türöffnungswinkel TÖW festlegen. Puffer (1) setzen.    Gestänge demontieren XX XX Teleskopschrauben (3) am Gestänge lösen: XX Teleskop auf Länge einstellen: àà mit Montageplatte: Maß H = 398 mm + Leibungstiefe L àà ohne Montageplatte: Maß H = 390 mm+ Leibungs­tiefe L XX XX Tür (2) in Offenlage bringen. Teleskopschrauben (3) lösen. Die Vorspannung löst sich, die gestrichelte Stellung wird erreicht. Gestänge demontieren.      Maß Y Standard Mit Achs­verlängerung Grundplatte 24 50 Montageplatte 22 48 Maß Z Standard Mit Achs­verlängerung Grundplatte 43 69 Montageplatte 48 74 Maß Y: Oberkante Lagerbock Gestänge – Unterkante des Antriebs Maß Z: Befestigungsbohrung des Gestänges – untere Befestigungsbohrung der Montageplatte/Grundplatte Befestigungsmittel für Gestänge Stahl-/ Aluminiumtüren … Zylinderschrauben M6 × 20 und Einnietmuttern M6 Germany GEZE GmbH Niederlassung Süd-West Tel. +49 (0) 7152 203 594 E-Mail: [email protected] GEZE GmbH Niederlassung Süd-Ost Tel. +49 (0) 7152 203 6440 E-Mail: [email protected] GEZE GmbH Niederlassung Ost Tel. +49 (0) 7152 203 6840 E-Mail: [email protected] GEZE GmbH Niederlassung Mitte/Luxemburg Tel. +49 (0) 7152 203 6888 E-Mail: [email protected] GEZE GmbH Niederlassung West Tel. +49 (0) 7152 203 6770 E-Mail: [email protected] GEZE GmbH Niederlassung Nord Tel. +49 (0) 7152 203 6600 E-Mail: [email protected] Holztüren … Holzschrauben mit Halbrundkopf Ø5 × 50 GEZE Service GmbH Tel. +49 (0) 1802 923392 E-Mail: [email protected] Austria GEZE Austria E-Mail: [email protected] www.geze.at Baltic States – Lithuania / Latvia / Estonia E-Mail: [email protected] Benelux GEZE Benelux B.V. E-Mail: [email protected] www.geze.be www.geze.nl Bulgaria GEZE Bulgaria - Trade E-Mail: [email protected] www.geze.bg GEZE GmbH Reinhold-Vöster-Straße 21–29 71229 Leonberg Germany China GEZE Industries (Tianjin) Co., Ltd. E-Mail: [email protected] www.geze.com.cn Iberia GEZE Iberia S.R.L. E-Mail: [email protected] www.geze.es Romania GEZE Romania S.R.L. E-Mail: [email protected] www.geze.ro South Africa GEZE South Africa (Pty) Ltd. E-Mail: [email protected] www.geze.co.za GEZE Industries (Tianjin) Co., Ltd. Branch Office Shanghai E-Mail: [email protected] www.geze.com.cn India GEZE India Private Ltd. E-Mail: [email protected] www.geze.in Russia OOO GEZE RUS E-Mail: [email protected] www.geze.ru Switzerland GEZE Schweiz AG E-Mail: [email protected] www.geze.ch GEZE Industries (Tianjin) Co., Ltd. Branch Office Guangzhou E-Mail: [email protected] www.geze.com.cn Italy GEZE Italia S.r.l E-Mail: [email protected] www.geze.it Scandinavia – Sweden GEZE Scandinavia AB E-Mail: [email protected] www.geze.se Turkey GEZE Kapı ve Pencere Sistemleri E-Mail: [email protected] www.geze.com GEZE Industries (Tianjin) Co., Ltd. Branch Office Beijing E-Mail: [email protected] www.geze.com.cn GEZE Engineering Roma S.r.l E-Mail: [email protected] www.geze.it Scandinavia – Norway GEZE Scandinavia AB avd. Norge E-Mail: [email protected] www.geze.no Ukraine LLC GEZE Ukraine E-Mail: [email protected] www.geze.ua Scandinavia – Denmark GEZE Danmark E-Mail: [email protected] www.geze.dk United Arab Emirates/GCC GEZE Middle East E-Mail: [email protected] www.geze.ae Singapore GEZE (Asia Pacific) Pte, Ltd. E-Mail: [email protected] www.geze.com United Kingdom GEZE UK Ltd. E-Mail: [email protected] www.geze.com France GEZE France S.A.R.L. E-Mail: [email protected] www.geze.fr Hungary GEZE Hungary Kft. E-Mail: [email protected] www.geze.hu Tel.: 0049 7152 203 … Fax: 0049 7152 203 310 www.geze.com Korea GEZE Korea Ltd. E-Mail: [email protected] www.geze.com Poland GEZE Polska Sp.z o.o. E-Mail: [email protected] www.geze.pl XX Slimdrive EMD invers EN Installation instructions Set the marking (4) for how far the inner shank (6) has to be pushed into the outer shank (8). EN Link arm  Fitting dimensions transom installation opposite hinge side Fitting dimensions for mounting plate DIN right/left mirrored  Fitting dimensions for direct attachment DIN right/left mirrored     XX 179938-01 XX XX    Install the lever (7) on the drive shaft and attach as marked. Attach the telescopic rod (5) to the door. Push the telescopic shanks inside one another up to the marking (4). Meanwhile pre-load the lever (7) by approx. 5°. Installing the link arm bearing block Follow separate installation instructions in situations involving the use of the sensor link arm. XX  Screw the link arm bearing block (1) on with … screws.      XX Tighten telescope screws (3) tightening torque 15 Nm. Mounting the link arm XX XX Open the door (2) an define door opening angle (TÖW). Set buffer (1).   Dismantling the link arm  XX XX Loosen the telescope screws (3) at the link arm. Set telescope to length: àà with mounting plate: dimension H = 398 mm + reveal depth L àà without mounting plate: dimension H = 390 mm + reveal depth L XX XX Move door (2) to open position. Loosen telescope screws (3). The pre-load is released, the dashed position is reached. Disassemble the link arm. Dimension Y Standard With spindle extension Base plate 24 50 Mounting plate 22 48 Dimension Y: Upper edge of the link arm bearing block – lower edge of the drive Dimension Z Standard With spindle extension Base plate 43 69 Mounting plate 48 74 Dimension Z: Fixing drill hole for the link arm – lower fixing drill hole for the mounting plate/base plate Fasteners for link arm Steel/aluminium doors … cylinder head screws M6 × 20 and riveting nuts M6 Timber doors … wood screws with button head Ø5 × 50 XX      Germany GEZE GmbH Niederlassung Süd-West Tel. +49 (0) 7152 203 594 E-Mail: [email protected] GEZE GmbH Niederlassung Süd-Ost Tel. +49 (0) 7152 203 6440 E-Mail: [email protected] GEZE GmbH Niederlassung Ost Tel. +49 (0) 7152 203 6840 E-Mail: [email protected] GEZE GmbH Niederlassung Mitte/Luxemburg Tel. +49 (0) 7152 203 6888 E-Mail: [email protected] GEZE GmbH Niederlassung West Tel. +49 (0) 7152 203 6770 E-Mail: [email protected] GEZE GmbH Niederlassung Nord Tel. +49 (0) 7152 203 6600 E-Mail: [email protected] GEZE Service GmbH Tel. +49 (0) 1802 923392 E-Mail: [email protected] Austria GEZE Austria E-Mail: [email protected] www.geze.at Baltic States – Lithuania / Latvia / Estonia E-Mail: [email protected] Benelux GEZE Benelux B.V. E-Mail: [email protected] www.geze.be www.geze.nl Bulgaria GEZE Bulgaria - Trade E-Mail: [email protected] www.geze.bg GEZE GmbH Reinhold-Vöster-Straße 21–29 71229 Leonberg Germany China GEZE Industries (Tianjin) Co., Ltd. E-Mail: [email protected] www.geze.com.cn Iberia GEZE Iberia S.R.L. E-Mail: [email protected] www.geze.es Romania GEZE Romania S.R.L. E-Mail: [email protected] www.geze.ro South Africa GEZE South Africa (Pty) Ltd. E-Mail: [email protected] www.geze.co.za GEZE Industries (Tianjin) Co., Ltd. Branch Office Shanghai E-Mail: [email protected] www.geze.com.cn India GEZE India Private Ltd. E-Mail: [email protected] www.geze.in Russia OOO GEZE RUS E-Mail: [email protected] www.geze.ru Switzerland GEZE Schweiz AG E-Mail: [email protected] www.geze.ch GEZE Industries (Tianjin) Co., Ltd. Branch Office Guangzhou E-Mail: [email protected] www.geze.com.cn Italy GEZE Italia S.r.l E-Mail: [email protected] www.geze.it Scandinavia – Sweden GEZE Scandinavia AB E-Mail: [email protected] www.geze.se Turkey GEZE Kapı ve Pencere Sistemleri E-Mail: [email protected] www.geze.com GEZE Industries (Tianjin) Co., Ltd. Branch Office Beijing E-Mail: [email protected] www.geze.com.cn GEZE Engineering Roma S.r.l E-Mail: [email protected] www.geze.it Scandinavia – Norway GEZE Scandinavia AB avd. Norge E-Mail: [email protected] www.geze.no Ukraine LLC GEZE Ukraine E-Mail: [email protected] www.geze.ua Scandinavia – Denmark GEZE Danmark E-Mail: [email protected] www.geze.dk United Arab Emirates/GCC GEZE Middle East E-Mail: [email protected] www.geze.ae Singapore GEZE (Asia Pacific) Pte, Ltd. E-Mail: [email protected] www.geze.com United Kingdom GEZE UK Ltd. E-Mail: [email protected] www.geze.com France GEZE France S.A.R.L. E-Mail: [email protected] www.geze.fr Hungary GEZE Hungary Kft. E-Mail: [email protected] www.geze.hu Tel.: 0049 7152 203 … Fax: 0049 7152 203 310 www.geze.com Korea GEZE Korea Ltd. E-Mail: [email protected] www.geze.com Poland GEZE Polska Sp.z o.o. E-Mail: [email protected] www.geze.pl

F 1206 turn fitting mounting instructions

F 1206 turn fitting mounting instructions

F 1206 turn fitting mounting instructions

Installation plan OL 320 with E 212 horizontal

OL 95 with E 212 horizontal

OL 95 with E 212 vertical

OL 95 with E 212 vertical

OL 95 with E 212 vertical

Installation plan gripping and cleaning scissors for aluminium profile